new supportV2.FCStd1

Soft/BOX/test/arro/arro.ino

@@ -0,0 +1,154 @@
+
+#include <OneWire.h>
+#include <DS18B20.h>  //temp DS18B20_RT by rob tillaart
+#include <DS3231.h>   //RTC DS3231 by andrew wickert
+#include <DHT.h>      //Adafruit
+#include <Wire.h>
+
+/*****************************************************************
+   Déclaration des Capteurs
+ *****************************************************************/
+//relay Lumiere
+const int RougeHaut      = 2;
+const int BleuHaut       = 3;
+const int RougeBas       = 4;
+const int BleuBas        = 5;
+
+//relay Ventilation
+const int DehumPin        = 6;
+const int Extracteur      = 7;
+const int VentilHaut      = 8;
+const int VentilBas       = 9;
+
+//relay Arrosage
+const int Arro1            = 10;
+const int Arro2            = 11;
+const int Evacuation      = 12;
+const int Melange         = 13;
+
+//Capteur niveau eau
+const int NiveauEauRecup  = 14;
+const int NiveauEauAqua   = 15;
+
+//Capteur Temp
+#define ONE_WIRE_TEMP 16
+OneWire oneWireTemp(ONE_WIRE_TEMP);
+DS18B20 Temp(&oneWireTemp);
+
+//capteur Hum air
+#define DHTTYPE DHT22
+#define DHTPIN 17
+DHT dht(DHTPIN, DHTTYPE);
+
+//Capteur hum sol
+const int HumidSolHaut = 18;
+const int HumidSolBas  = 19;
+
+//interupteur
+const int interType  = 22;
+const int interLum  = 24;
+const int interONExt  = 26;
+const int interONVentil  = 28;
+const int interOFFExt  = 30;
+const int interONAro  = 32;
+const int interONVid  = 34;
+const int interOFFAro  = 36;
+const int inter9  = 38;
+const int inter10 = 40;
+
+//RTC
+DS3231 Clock;
+
+/*****************************************************************
+   Déclaration des Variables globals
+ *****************************************************************/
+
+//Variable lumiere
+int newDay = 1; // Variable pour savoir si nouveau jour.
+int HA;  //heure allumage en minute
+int HE;  //heure extinction en minute (Ha +12Hou18H +/-15min)
+
+//Variable Extraction
+int tmpExtract = 0, humExtract;
+int extract;
+
+//Variabe Arrosage
+const int delaySecArro = 20;
+const int delaySecEvacuation = 30;
+int SolBas, SolHaut;
+int HeuArrosage;
+/***********************************************************************
+     Setup
+ **********************************************************************/
+
+void setup() {
+  Serial.begin(9600);
+
+  /***********************************************************************
+    init des pins
+  * *********************************************************************/
+  //PIN Lumiere
+  pinMode(RougeHaut, OUTPUT);
+  pinMode(RougeBas, OUTPUT);
+  pinMode(BleuHaut, OUTPUT);
+  pinMode(BleuBas, OUTPUT);
+  digitalWrite(RougeHaut, HIGH);
+  digitalWrite(RougeBas, HIGH);
+  digitalWrite(BleuHaut, HIGH);
+  digitalWrite(BleuBas, HIGH);
+
+  //Pin ventilation
+  pinMode(DehumPin, OUTPUT);
+  pinMode(Extracteur, OUTPUT);
+  pinMode(VentilHaut, OUTPUT);
+  pinMode(VentilBas, OUTPUT);
+  digitalWrite(DehumPin, HIGH);
+  digitalWrite(Extracteur, HIGH);
+  digitalWrite(VentilHaut, HIGH);
+  digitalWrite(VentilBas, HIGH);
+
+  //Pin Arrosage
+  pinMode(Arro1, OUTPUT);
+  pinMode(Arro2, OUTPUT);
+  pinMode(Evacuation, OUTPUT);
+  pinMode(Melange, OUTPUT);
+  digitalWrite(Arro1, HIGH);
+  digitalWrite(Arro2, HIGH);
+  digitalWrite(Evacuation, HIGH);
+  digitalWrite(Melange, HIGH);
+
+
+
+}
+/*
+  const int Arro1            = 10;
+  const int Arro2            = 11;
+  const int Evacuation      = 12;
+  const int Melange         = 13;
+*/
+int incomingByte = 0; // for incoming serial data
+
+void loop() {
+
+
+  if (Serial.available() > 0) {
+    // read the incoming byte:
+    incomingByte = Serial.read();
+    if (incomingByte == 'a') {
+      Serial.println("ON1");
+      digitalWrite(Arro1, LOW);
+    }
+    if (incomingByte == 'z') {
+      Serial.println("ON2");
+      digitalWrite(Arro2, LOW);
+    }
+    if (incomingByte == 'q') {
+      Serial.println("OFF1");
+      digitalWrite(Arro1, HIGH);
+    }
+    if (incomingByte == 's') {
+      Serial.println("OFF2");
+      digitalWrite(Arro2, HIGH);
+    }
+  }
+}